INCRA MITEREXPRESS Miter Express

Included hold down clamp and twin t-slots for secure cutting. Doubles any miter gauge's crosscut range Up To 24", Safely Handles Both Extra Large And Extra Small Work pieces. Removable t-slot Retaining Clips & Adjustable Miter Bar. This sled is a sliding, miter-cutting Platform That Fully Supports And Controls Your Work piece Throughout The Cut.

Dock and lock" any Miter Gauge in seconds. Other features include two embedded t-tracks to secure the included hold Down Clamp To Anchor Your Work piece, A Locking Drop Panel That Supports The Offcut, And Also Provides Zero Clearance Tear Out Control. Once docked, it stays put until you Undock It To Switch Back To Your Regular Miter Gauge.

Miter gauges drag your board across the table, a Sled Slides The Work piece Giving More Support And Control Creating Better, More Consistent Cuts. Provides zero clearance for safe and accurate cutting. Note: miter gauge Shown In Photo Available Separately. Upgrade any miter gauge To A Miter Sled In Seconds.

The sled features a built in miter bar that is adjustable for zero side play tracking, So Even If Your Old Miter Gauge Is Loose In The Miter Slot It Becomes Rock Solid Once Its Locked Into The Express. Eliminates all side play between Table Saw's Miter Slot And Any Miter Gauge. The miter express is designed to let You Instantly Drop And Lock Your Miter Gauge Into The Sliding Platform.

---

INCRA Miter1000/HD Miter Gauge

Are you cutting parts for segmented turning? the miter 1000HD will allow you to precisely set and quickly duplicate any angle you might need, whether it's 18 degrees for cutting 10 sides, 25. 7 degrees for 7-sided objects, or anything else imaginable. Six expansion disks adjust both sides of the bar for ZERO side play, including Delta, Craftsman, low-friction travel on most table saws with standard miter gauge channels, imports, etc.

. Please refer to Incra. Com for fit chart before ordering. The hd stands for high definition, because the protractor plate's exclusive AngleLOCK Indexing System has a whopping 180 angle stops in 1degree increments with special stops located at 22. 5 degrees. The miter 1000's adjustable miter bar will fit square-sided miter slots measuring 3/4" wide, 3/8" deep, and with or without a 15/16" T-slot at the bottom.

1/10th-degree vernier cursor, telescoping Fence Expands from 18-Inch to 31-Inch Overall Length. Heavy duty machined and laser cut Components. The new incra miter 1000hd is the most refined model yet in the Miter 1000 series.


Similar products:

---

INCRA Build-It Hold Down Clamp

Patented incremental Flip Shop Stop for Prefect Cut Length Control. The "glue" that holds everything together is INCRA's innovative NEW T-Slot Panel Connector. An ideal accessory for the Build-It system family of tools. Removable retaining Clip for T-Slot Miter Channels. These specially designed aluminum components serve to simultaneously interconnect the panels and provide a rock solid T-Slot for adding and holding Build-It Hold Down Clamps.

Patented glide lock miter Bar Expansion Disks Provide a Perfect Fit. Locks a workpiece into place for consistent cutting results. 1/10th-degree vernier cursor, telescoping Fence Expands from 18-Inch to 31-Inch Overall Length. Sturdy aluminum component construction. Heavy duty machined and laser cut Components.

Exclusive captured pivot design provides hassle free clamping. Work with all incra Track and Incra T-Track components and accessories. 180 angle lock indexing stops with 1-degree Step Spacing and Special Stops at ±22-1/2-Degree.


Similar products:

---

INCRA I-BOX Jig for Box Joints

Works with the metric HingeCrafter, too. If you've been looking to improve your shop's joinery capabilities with a fast, versatile, and easy to use method for producing box joints of all descriptions, the INCRA I-Box is what you've been waiting for. Exclusive incra glidelock miter bar fits standard 3/4-Inch x 3/8-Inch miter slots with a 0

740-inch - 0762-inch adjustment range. Reversible and reusable MDF sub fence dramatically reduces or eliminates tearout. Sturdy aluminum component construction. Locks a workpiece into place for consistent cutting results. Use it on your table saw or router table to cut great looking box joints. An ideal accessory for the Build-It system family of tools.

To get right to the point, the new Incra I-Box is the most advanced tool ever produced. 180 angle lock indexing stops with 1-degree Step Spacing and Special Stops at ±22-1/2-Degree. At the same time, it's easy to use and the included 1 hour instructional DVD covers everything from basic setup to advanced decorative joinery.

To get right to the point, the new inCRA I-Box is the most advanced tool ever produced for creating a stunning variety box joints & finger joints. The splined box joint is yet another incra-only decorative joint that's guaranteed to add wow-factor to your projects, and the I-Box can even be used to produce an unlimited variety of classic dentil mouldings.

Patented incremental Flip Shop Stop for Prefect Cut Length Control.


Similar products:

---

Incra MITER1000SE Miter Gauge Special Edition With Telescoping Fence and Dual Flip Shop Stop

Exclusive dual-pitch lead screw mechanism for fast micro-adjusting and a broad 1/8-Inch - 3/4-Inch range of pin widths. Its revolutionary design allows faster setup, greater versatility, and improved user safety compared to traditional jigs. Exclusive incra glidelock miter bar fits standard 3/4-Inch x 3/8-Inch miter slots with a 0

740-inch - 0762-inch adjustment range. Exclusive captured pivot design provides hassle free clamping. Patented glidelocK miter bar with 6 expansion points for quick repeats. To get right to the point, the new Incra I-Box is the most advanced tool ever produced. Removable retaining Clip for T-Slot Miter Channels.

18- to 31-inch telescoping incremental miter fence for handling a variety of stock widths. Sturdy aluminum component construction. 41 laser cut v-stops for extreme accuracy at all popular angles. Engraved stainless steel primary scale for precision accuracy. Locks a workpiece into place for consistent cutting results.

Reversible and reusable MDF sub fence dramatically reduces or eliminates tearout. Reversible design works on either side of the cutter.


Similar products:

---

Wixey WR25 Mini Digital Height Gauge

An ideal accessory for the Build-It system family of tools. Reversible design works on either side of the cutter. Displays inches with fractions or millimeters. The wixey wr25 mini digital height gauge is a Light Weight, Easy to Use Gauge for all Types of Wood Working Applications. Its revolutionary design allows faster setup, greater versatility, and improved user safety compared to traditional jigs.

Exclusive dual-pitch lead screw mechanism for fast micro-adjusting and a broad 1/8-Inch - 3/4-Inch range of pin widths. The fractions are displayed using Precise Fraction Technology which Gives you 4 Times The Accuracy of Other Fraction Readouts. Exclusive incra glidelock miter bar fits standard 3/4-Inch x 3/8-Inch miter slots with a 0

740-inch - 0762-inch adjustment range. Heavy duty machined and laser cut Components. 18- to 31-inch telescoping incremental miter fence for handling a variety of stock widths. Patented incremental Flip Shop Stop for Prefect Cut Length Control. Engraved stainless steel primary scale for precision accuracy. Incra flip shop stop-Fence Positioner for optimal mitering accuracy.

1/10th-degree vernier cursor, telescoping Fence Expands from 18-Inch to 31-Inch Overall Length.


Similar products:

---

MICRODIAL Tapering Jig for Table Saw, Router Table, and Band Saws for Woodworking Works with GRR-RIPPER

Sturdy aluminum component construction. Locking rule for repeat setting. 1/10th-degree vernier cursor, telescoping Fence Expands from 18-Inch to 31-Inch Overall Length. Reversible design works on either side of the cutter. Displays inches with fractions or millimeters. The addition of the grr-ripper will allow users to pressure in three dimensions: downward, inward, and forward; this will virtually eliminate kickback and should alwasy be used when cutting narrow or small workpieces.

The microdial tapering jig by mICROJIG helps you achieve cutting edge tapers. At the same time, it's easy to use and the included 1 hour instructional DVD covers everything from basic setup to advanced decorative joinery. Exclusive incra glidelock miter bar fits standard 3/4-Inch x 3/8-Inch miter slots with a 0

740-inch - 0762-inch adjustment range. Measure bore and slot depths with the plunger attachment. Meanwhile, tapers can be cut from an infinite range between 0˚ to 10˚ with 1/8˚ incremental stops. Locks a workpiece into place for consistent cutting results. Reversible and reusable MDF sub fence dramatically reduces or eliminates tearout.

Lays flat for fence to blade or bit positioning.


Similar products:

---

Freud Box Joint Cutter Set, Cuts 1/4 In. and 3/8 In. Joints SBOX8

Locks a workpiece into place for consistent cutting results. 41 laser cut v-stops for extreme accuracy at all popular angles. Cut up to 8-sided tapered legs together with the GRR-RIPPER 3D Pushblock. An ideal accessory for the Build-It system family of tools. Patented glide lock miter Bar Expansion Disks Provide a Perfect Fit.

Use it on your table saw or router table to cut great looking box joints. 1/10th-degree vernier cursor, telescoping Fence Expands from 18-Inch to 31-Inch Overall Length. Its revolutionary design allows faster setup, greater versatility, and improved user safety compared to traditional jigs. Patented glidelocK miter bar with 6 expansion points for quick repeats.

Use on all table saws for cutting grooves to create box joints in softwood or hardwood. Reversible design works on either side of the cutter. Exclusive freud tiCo Hi-Density Carbide for clean, flat-bottom grooves. Measure bore and slot depths with the plunger attachment. Heavy duty machined and laser cut Components.

. Sturdy aluminum component construction.


Similar products:

---

Incra FLIPSHOPSTOP Adjustable Dual, FLIP-Shop Stop Positioner for the Flip Fence only

Coating reduces heat and drag, enabling the blade to last longe. 18- to 31-inch telescoping incremental miter fence for handling a variety of stock widths. Heavy duty machined and laser cut Components. The flip shop stop works great with all INCRA Flip Fences. 41 laser cut v-stops for extreme accuracy at all popular angles.

With multiple stop rods included and Dual-Arm construction, there is no situation it cant handle. It is not compatible with standard incralock cut-off Miter Gauge Fences, INCRA Track Systems, or INCRARouter Fences. Positive Stop for Mitered Boards. Full instructional DVD and bonus project plans included. Sbox8 makes box joint construction easy with strong and accurate joints No shims or adjustments needed.

Two independent MemoryLocks keeps angles for repeat taper cuts. This stop gives you the most options and best performance of any stop on the market. We even designed interlocking grooves in the arms and fence so that a sharply mitered workpiece cant slip behind the stop to give you an inaccurate cut. Engraved stainless steel primary scale for precision accuracy.

Its revolutionary design allows faster setup, greater versatility, and improved user safety compared to traditional jigs. Patented glide lock miter Bar Expansion Disks Provide a Perfect Fit.


Similar products:

---

MICROJIG GRGH-040 GRR-RIPPER Gravity Heel Kit

Incra flip shop stop-Fence Positioner for optimal mitering accuracy. Work Safer. Great for resawing on the bandsaw, face jointing on the jointer/planer, coping on the router table, and hand-over-hand feeding on the table saw. It can also be used as a template for repeat routing. Its revolutionary design allows faster setup, greater versatility, and improved user safety compared to traditional jigs.

Work Smarter. Displays inches with fractions or millimeters. The unique design provides extra leverage to helppush through the cut and prevent blowout. Cut up to 8-sided tapered legs together with the GRR-RIPPER 3D Pushblock. Precision taper cuts as accurate as 1/8 of a degree. Reduces blowout and tearout on the table saw and router table.

Coating reduces heat and drag, enabling the blade to last longe. The gravity heel is there when you need it and get out the way when you don’t. Removable retaining Clip for T-Slot Miter Channels. Patented glidelocK miter bar with 6 expansion points for quick repeats. Accessory Parts Included. 18- to 31-inch telescoping incremental miter fence for handling a variety of stock widths.




Similar products:

---

Leecraft DW-2 Zero-Clearance Table Saw Insert for DeWalt Model DW744 and DW746

Use it on your table saw or router table to cut great looking box joints. Engraved stainless steel primary scale for precision accuracy. Measures 13-5/8-by-3-3/4 inches LxW. Exclusive dual-pitch lead screw mechanism for fast micro-adjusting and a broad 1/8-Inch - 3/4-Inch range of pin widths. Mounting Hardware Included.

Made in the usa. Locks a workpiece into place for consistent cutting results. Precision taper cuts as accurate as 1/8 of a degree. Two independent MemoryLocks keeps angles for repeat taper cuts. Exclusive captured pivot design provides hassle free clamping. Sbox8 makes box joint construction easy with strong and accurate joints No shims or adjustments needed.

Removable retaining Clip for T-Slot Miter Channels. Positive Stop for Mitered Boards. Grr-ripper gravity heel accessory is a fully adjustable heel with auto-retracting technology for reducing blowout. Router table gravity heels provide a secure backing to routing operations to prevent blow out. Coating reduces heat and drag, enabling the blade to last longe.

To get right to the point, the new Incra I-Box is the most advanced tool ever produced.


Similar products: